Seats and Restraints
Head Restraints
Warning: With head restraints that are not installed and adjusted
properly, occupants have a greater chance of neck or spinal injury in a crash.
Do not drive until all head restraints are installed and adjusted properly.
Front Seats
The vehicle's front seats have adjustable head restraints in the outboard seating
positions. Adjust the head restraint so that the top of the restraint is at the
same height as the top of the occupant's head. This reduces the chance of a
neck injury in a crash.
To raise or lower the head restraint, press the button on the side and pull up
or push down, then release the button. Pull and push after releasing to ensure
it is locked. Front outboard head restraints are not removable.
Rear Head Restraints
The rear seat has head restraints in the outboard positions that cannot be adjusted.
They can be folded forward when the rear seat is unoccupied. Press the button on
the side to fold and always return to upright when occupied.
For child restraints in the rear seat, see LATCH System.
Center Headrest
The center rear seat may have a non-adjustable headrest. For child restraints,
see LATCH System.
Front Seats
Seat Adjustment
Warning: Adjusting the driver seat while moving can cause loss of control.
Only adjust when the vehicle is stationary.
To adjust a manual seat:
- Pull the handle at the front of the seat.
- Slide to the desired position and release the handle.
- Check that the seat is locked by trying to move it back and forth.
See Reclining Seatbacks and Lumbar Adjustment for additional seat adjustments.
Center Seat
If equipped, the center front seatback doubles as an armrest and cupholder/storage
area. Pull the strap to fold it. Do not sit on it when folded.
Power Seat Adjustment
To adjust a power seat:
- Slide the seat forward or rearward.
- Raise/lower the front part of the seat cushion.
- Raise/lower the rear of the seat.
- Adjust seatback using the recline control.
- Adjust lumbar support if equipped.
Some vehicles have a vibrating pulse alert in the driver seat for crash prevention.
Lumbar Adjustment
Press and hold the control forward to increase or rearward to decrease upper and
lower lumbar support simultaneously.
Reclining Seatbacks
Warning: Reclining while the vehicle is moving can be dangerous.
Seat belts may not protect you properly. Always sit upright and wear the seat belt
correctly when moving.
Manual Reclining Seatbacks
Warning: If seatbacks are not locked, they may move forward during
a sudden stop or crash, causing injury.
- Lift the lever to fold the seat forward or recline.
- Move the seatback to the desired position, release the lever to lock.
- Push and pull to ensure it is locked.
- To return upright, lift the lever fully and let the seatback return, then lock.
Power Reclining Seatbacks
Tilt the top of the control rearward to recline and forward to raise.
Memory Seats
If equipped, memory seats allow two drivers to save seat and mirror positions,
plus a shared exit position. Memory positions are linked to RKE transmitter 1 or 2.
Before saving, adjust all memory features, then press SET, followed
immediately by pressing and holding 1, 2, or B
until two beeps sound.
Vehicle Personalization Settings
- Seat Entry Memory: enable to start movement when the vehicle is turned on.
- Seat Exit Memory: enable to recall B position when the vehicle is turned off and driver door opened.
- See Vehicle Personalization for more settings.
Identifying Driver Number
- Move your RKE transmitter away from the vehicle.
- Start with another key/transmitter. DIC shows driver number. Turn off and remove key.
- Start with your initial transmitter. DIC shows your driver number.
Saving Memory Positions
- Turn vehicle on or to ACC/ACCESSORY.
- Adjust all memory features.
- Press and release SET, beep sounds.
- Immediately press and hold 1 or 2 until two beeps sound.
- Repeat for a second driver if needed.
Manually Recalling Memory Positions
Press and hold 1, 2, or B to recall positions.
Release or adjust power seat, mirrors, or SET to stop recall.
Seat Entry Memory
If enabled, RKE transmitters 1 or 2 automatically recall saved positions when
turning the vehicle on. Seat Entry Memory requires the shift lever in P (Park).
Seat Exit Memory
Seat Exit Memory is saved to B and recalled automatically when the
vehicle is turned off and the driver door is opened. Press any memory control to
stop movement.
